Choose options
Overview
Single-seat full-spectrum infrared cabin. Two quartz heaters, four carbon panels, and a 660nm/850nm ceiling panel. Plugs into a standard outlet.
A one-person footprint at 31.5 inches wide, built to the same specification as the larger Onyxeek cabins rather than stripped down to fit. Full-spectrum quartz and ultra low EMF carbon run together, with red and near-infrared overhead and a heated foot panel below.
Quartz and Carbon Together
Two heater types run in the same cabin. The full-spectrum quartz elements produce near, mid and far infrared across 0.8–23.3 micrometers and come up fast. The ultra low EMF carbon panels behind the back and side slats hold a broad, even far-infrared field once the cabin is warm. Quartz gets you to temperature; carbon keeps the heat uniform rather than concentrated at one wall.
Red and Near-Infrared Overhead
The ceiling panels emit 660nm red and 850nm near-infrared. Running light at the start of a heat session keeps both exposures in one place, with no separate device to position or plug in. The foot panel below is a far-infrared carbon element over tourmaline stones.
Plugs Into a Normal Outlet
This cabin runs on a standard 110–120V household circuit. No dedicated line, no hardwiring and no electrician — which is the practical difference between an infrared cabin and a traditional electric sauna at this size. Installation is tool-free and takes about 20 minutes. The cabin is ready to sweat in 10–12 minutes and reaches 150°F in roughly 20.
Specifications
- Occupancy: 1 person
- Sauna Type: Full-spectrum infrared — quartz and carbon
- Exterior Dimensions: 31.5" W × 35.4" D × 67" H (800 × 900 × 1700 mm)
- Wattage: 1,600W
- Heaters: 2 full-spectrum quartz
- Carbon Panels: 4 ultra low EMF far infrared — back and sides
- Foot Panel: 1 far-infrared carbon with tourmaline stones
- Ceiling Light Panel: 1 × 660nm red + 850nm near-infrared
- Maximum Temperature: 150°F (66°C)
- Warm-Up: Ready in 10–12 minutes; 150°F in about 20 minutes
- Voltage: 110–120V standard household outlet — no electrician required
- EMF: Less than 2 mG at the seated position
- Wavelength Range: 0.8–23.3 µm (near, mid and far infrared)
- Light Therapy: 660nm red + 850nm near-infrared
- Wood: 100% Canadian hemlock, all-black exterior
- Glass: 0.31 inches (8 mm) tempered, front door
- Interior: No glue — free of VOCs and formaldehyde
- Control: Digital panel for time and temperature
- Connectivity: Wi-Fi with Burneek app; Bluetooth and USB audio
- Lighting: 3 linear ambient LED strips — ceiling, back wall, under seat
- Air: Integrated ionizer and a built-in cabin vent
- Assembly: Tool-free, about 20 minutes
- Certifications: UL, ETL, CE, ISO 9000
- Warranty: 2-year Burneek warranty
- Location: Indoor use only
What Is Included
- Burneek Onyxeek 1-person cabin with integrated heaters and panels
- 2 full-spectrum quartz heaters
- 4 ultra low EMF far-infrared carbon panels
- 1 far-infrared carbon foot panel with tourmaline stones
- 1 ceiling light panel — 660nm red + 850nm near-infrared
- Built-in audio system — Bluetooth and USB
- User manual and setup guide
- 2-year Burneek warranty
Disclaimer
This product is intended for general wellness use only. It is not a medical device and is not intended to diagnose, treat, cure, or prevent any disease or medical condition. Consult a qualified healthcare provider before use if you have a cardiovascular condition, are pregnant, or are managing a chronic illness. Always hydrate adequately before and after sessions.
A full-spectrum cabin that fits in a corner
SPECIFICATION
What you are buying.
-
31.5 inches wide
Exterior 31.5" W × 35.4" D × 67" H. A corner, not a room.
-
Two heater types
2 full-spectrum quartz elements plus 4 ultra low EMF carbon panels on the back and sides.
-
0.8 to 23.3 µm
Near, mid and far infrared, plus a 660nm and 850nm ceiling panel.
-
1,600W on a normal outlet
110–120V household circuit. No dedicated line, no hardwiring.
-
Under 2 mG seated
Measured at the seated position, not at the wall.
-
20-minute assembly
Tool-free. Ready to sweat 10–12 minutes after that.
HOW A SESSION RUNS
A session, start to finish.
Nothing to plumb, nothing to drain, nothing to schedule around.
Preheat
Set it going and leave the door shut. The cabin is ready to sweat in 10 to 12 minutes and reaches 150°F in about twenty — the quartz elements do the fast work while the carbon panels even the heat out.
Heat
Twenty to thirty minutes is the usual range once you are used to it. Start at 10 to 15. The Onyxeek runs the red and near-infrared ceiling panel at the same time, so the light session is not a separate appointment.
Cool down
Open the door, sit, drink. The cool-down is where most of the cardiovascular adaptation is thought to happen, so it is not the part to rush.
No electrician, no ventilation, no construction
